Re: [Harp-L] Breaking in speakers (Ted Weber method)

["hazcon" <hazcon@xxxxxxxxxx>]

I must be missing something here but why not just plug a CD player or radio 
into an amp and leave it going,as loud as you want, for as long as it takes.
No danger of over stressing the speaker and wouldn't the more complete 
spectrum of frequencies be better than a monotone?
Just curious
Rick
in NZ
----- Original Message ----- 
From: "George Brooks" <gbrooks@xxxxxxxxxxx>
To: "Harp-L" <harp-l@xxxxxxxxxx>
Sent: Wednesday, June 24, 2009 15:09
Subject: [Harp-L] Breaking in speakers (Ted Weber method)


> Below is a cut-and-paste on breaking in speakers from Ted Weber's FAQ . I 
> have used his method on two different amps with great results each time. 
> The FAQ is at:
>
> http://www.webervst.com/sptalk.html
>
> You will have to scroll down quite a ways.  The cut-and-paste below gives 
> you all you need to know, but the FAQ entry also contains, at the bottom, 
> a handy little applet that lets you plug in the speaker impedance and 
> power rating and calculates the break-in voltage for you.
>
> Warning: this method produces a very loud hum.  You will probably not want 
> to be in the same place as you amp or speaker while this is going on.
>
> ===========================
>
> From: Jeff Brinson
>
> I recently purchased a replacement 12" speaker for my amp. I like its 
> tone, but it seems a little shy on the low end and a little tight overall. 
> Is there anything I can do to loosen it up or improve its tone? I've heard 
> of people beating on the magnet and other methods, but I'd like to know 
> what you suggest.
>
> Jeff, most speakers are a little tight when new due to the stiffness of 
> the cone surround and spider. After several hours of playing at high 
> levels, they begin to loosen up and have more overall body and sound 
> projection. I've heard of beating on the magnet also, and quite frankly, 
> I'm not sure what benefit it is supposed to yield. An AlNiCo magnet is a 
> metal alloy, so it conducts electricity. This means that physical shock 
> will cause the magnet to induce an electrical current into itself, which 
> will in turn generate a magnetic field, and that field, if strong enough, 
> can partially demagnetize the magnet. A ceramic magnet, on the other hand, 
> is essentially non conductive and therefore has a very high resistance. 
> That's the reason powdered ferrites are used in high frequency coils and 
> transformers, so currents won't be induced in the core and adversely 
> affect the transformer action at high frequencies. Ceramic speaker magnets 
> are also made of powdered ferrites. If a person was purposely trying to 
> decrease some of the magnetism of a speaker, the intent is probably to 
> lower the self damping of the speaker itself thereby allowing the speaker 
> resonance to add some low end. In my opinion, that's a poor method of 
> increasing the low end.
> OK, on to 'breaking in' a speaker. If you really want to speed up the 
> breaking in period, the easiest method is to connect the speaker to a 
> filament transformer. Having said that, let's look at the precautions you 
> need to take. Since you will be driving the speaker with a steady state 
> signal, you don't want to drive it at its rated power or it will burn up 
> the voice coil. 1/3 power rating is a safe figure to use. So, let's say 
> you have a 50 watt speaker and it is 8 Ohm. 1/3 power is about 17 watts, 
> and at 8 Ohm, that works out to be around 11.5 volts. Using a 12.6 volt 
> transformer will put 20 watts into the speaker. I wouldn't have a problem 
> with that in our products, but just to be safe, you might want to go with 
> a 6.3 volt filament voltage, which will put about 5 watts into your 
> speaker. Another option is to use a variac into the primary side of the 
> 12.6 volt filament transformer and dial in the voltage you want on the 
> secondary. That way, you can dial in the 11.5 volts we originally 
> calculated at the 1/3 power level. I'd also suggest performing the 
> operation in a garage or closet, because listening to the loud 60hz hum 
> from the speaker will grate on your nerves very quickly. Also, if you 
> leave the speaker out of the cabinet, the rear radiation of the speaker 
> will cancel alot of the front radiation and reduce the noise. You need to 
> lay the speaker face up though, so the cone can move as much as possible 
> since the whole idea of this operation is to loosen up the cone and 
> spider. Laying the speaker face down would trap air between the cone and 
> the surface of the table and restrict cone movement. You're going to be 
> surprised how much the cone moves and how loud the speaker is, even at 1/3 
> power.
> Here's the math for determining the correct voltage to use in case you 
> have a different wattage and impedance rating than our example above:
> 1. Take the power rating of the speaker and divide it by 3.
> 2. Take that number and multiply it by the speaker's Ohm rating (4, 8, or 
> 16)
> 3. Use your calculator to find the square root of that number.
> 4. The result is the voltage you need to use to drive the speaker at 1/3 
> its rated power.
>
> _______________________________________________
> Harp-L is sponsored by SPAH, http://www.spah.org
> Harp-L@xxxxxxxxxx
> http://harp-l.org/mailman/listinfo/harp-l