RE: [Harp-L] Zoom H4 + Simple Recording Setup

["Bill Hines" <billhines4@xxxxxxxxxxx>]

Right, the micro-track has a switch on the side - L/M/H so be sure you
have the proper setting for this in regard to what mic you are using.
This caused trouble for me as well at first. Read the manual carefully,
and make sure to get the latest firmware upgrade from the m-audio
website and put it on your microtrack - there were some firmware bugs
earlier that caused this type of problem.

Bill Hines
Hershey, PA

-----Original Message-----
From: harp-l-bounces@xxxxxxxxxx [mailto:harp-l-bounces@xxxxxxxxxx] On
Behalf Of Richard Hunter
Sent: Thursday, August 02, 2007 11:13 AM
To: harp-l@xxxxxxxxxx; fssharp@xxxxxxxxx
Subject: Re: [Harp-L] Zoom H4 + Simple Recording Setup

fssharp wrote:

<I went with the Microtrack due to many favorable reviews (on harp-L and

<elsewhere) and mainly due to size, ease of navigation, and hopefully 
<superior sound,  But with the included T-mic I got horrible noise on 
<"Low" sensitivity and with faders at 50%.  I've returned it and am 
<awaiting a replacement, thinking there was something wrong with it. <
<But maybe I am kidding myself and the T-mic will always have hiss/roar 
<for acoustic recordings at moderate volumes.  If so, I will have to 
<think about the Zoom if it's built in electret mics are that much 
<better than the one provided with the Microtrack.  Anyone know how 
<these compare?  Was my original MT unit ok and that noise with the 
<T-mic typical?  Anyone compare S/N on these two units with the electret

<mics?  I wish I could have side-by-sided them, but Guitar Center 
<doesn't carry Zoom (Samson product).  Any advice on what to expect when

<my replacement MT arrives (hopefully this week) would be greatly 
<appreciated.

Your problem is probably about how you're setting up to record, not 
about the Microtrack per se.

Hiss or roar is usually the result of a recording level that's too low 
(hiss) or too high (roar).  First, you need to set the recording level, 
or the input level on the mics.  You're already doing that, so the next 
question is: what else is the machine doing that needs adjustment from
you?

The Zoom has an automatic limiter that's supposed to stop overloaded 
record levels.  But I've found that I have to be careful about where I 
set the input level (low, medium, or high)--if I set the level to HIGH 
with a loud rock band, it overloads pretty quick.  Also, I have to be 
careful to push the record button once to let the recorder get a level 
(while the band is playing!), before I press it again to start the 
recording--if it doesn't get a level first with something that's more or

less representative of the highest sound level, overloading (which is 
your roar) is likely.  If you don't set the levels right on the Zoom, 
even a recording of a solo acoustic harp sounds bad.  Set them right, 
and the results  range from good to amazingly good, depending on the 
sound of the room itself.

Your Microtrack probably has similar functions.  I recommend that you 
read the manual to find out how to get the best results.  These units 
are simple, and they can produce great results. But to get great results

from any piece of equipment, you have to know how to work the thing. 
Fortunately, in this case, there probably aren't a lot of settings to 
work with.  Half an hour with the manual should make you an expert.

Regards, Richard Hunter
hunterharp.com
latest mp3s always at http://broadjam.com/rhunter
_______________________________________________
Harp-L is sponsored by SPAH, http://www.spah.org Harp-L@xxxxxxxxxx
http://harp-l.org/mailman/listinfo/harp-l